Question 1

Common engine and gearbox issues with the 2015 Holden Colorado

Accepted Answer

The biggest issue owners have experienced with this car is a tendency for the engine to consume oil and require a top-up between oil changes. Holden addressed this by changing the specification of the oil from a 5W30 to a 5W40 oil and released a new oil cap design. You’ll know if the new-design oil cap is fitted to your car as the owner’s manual will have been altered by a Holden dealer to reflect the new oil specification. Beyond that, the biggest driveline complaint seems to be the noise generated by the engine. However, this seems to be a natural by-product of the 2.8-llitre turbo-diesel fitted to the Colorado 7 and is not a fault per se.

Question 2

2018 Holden Colorado has leaks in the top near the brake light

Accepted Answer

Not every Colorado suffers this problem, but there are certainly a percentage that do. It’s a relatively common thing with this model and the first sign is a stain that develops on the roof lining in the rear seat just above the rear window. It’s caused by water entering the cabin through the high-mount brake light assembly. The problem is caused by the light’s seals that fail over time, and the fix is to remove the light, clean the area around it and then seal it with panel sealer (or something similar) from the outside. If you’re fussy, you can replace the whole light assembly, but that won’t fix the failed seal, so you’ll still need to reseal the area where the light mounts.

Question 3

The steering shaft lower spline to steering rack in my 2016 Holden Colorado RG7 Trailblazer is loose

Accepted Answer

You really can’t afford to take any chances with a car’s steering system. The thought of this crucial system failing even at low speeds doesn’t bear thinking about, so if there’s any play or looseness in the system, it needs to be diagnosed and fixed properly with new parts if necessary. Meantime, Loctite and other thread-locking products are designed to stop fasteners coming loose. These products are not designed to take up slack in worn parts and shouldn’t be used that way. Even if the thread-locker stops the fastening nut coming loose, it won’t do anything about the slack in the joint you’ve already noted.

Question 4

2009 Holden Colorado check engine light and limp mode are coming on

Accepted Answer

I think you’re on the right track by concentrating on the information being conveyed by the crank-angle sensor. But the problem is more likely to be a stretched timing chain rather than a dud sensor. The V6 engine in your Colorado is notorious for this problem and, when it happens, it throws the camshafts out of synch with the crankshaft. When the crank-angle sensor and the camshaft-angle sensor can’t agree that the positions of the crankshaft and camshafts relative to each other are correct, the problems start. This lack of synchronisation is one of the things the crank-angle sensor is paid to look for and why it’s limiting engine speed or not allowing the engine to start at all. By clearing the fault code and disconnecting the crank-angle sensor, you’re stopping the error information being sent to the ECU and the ute starts first time (it’s probably taking a camshaft-angle reference when it can’t find the crank-angle information).

Question 5

My 2015 Holden Colorado isn't starting

Accepted Answer

The starter motor would be a very good place to start looking for the problem. If the battery checks out (and that presumes you’ve load tested it, not just run a voltmeter across its terminals) and the addition of a second jump battery only just turned the engine over, then, the starter motor is a likely suspect. But don’t forget things like a poor earth somewhere on the car or a dodgy ignition or starter button. Once the engine is running, check the power going into the battery. You should be looking at between 13.2 and 14.5 volts going into the battery with the engine running if the alternator is pulling its weight. Just because the battery indicator is showing green, does not mean categorically that it’s in good health. It can produce a surface charge that might show 12 volts with no load on it, but can fall to its knees when you load it up with the starter motor.

Question 6

Fuel economy issues in my 2019 Holden Colorado Z71

Accepted Answer

There could be a complex, electronic, fuel-supply or engine-management reason for this, and if that's the case, having the vehicle scanned would be a good place to start. Or, it could be a case of human behaviour that is skewing your fuel economy figures. By which, I mean that when you got the car brand-new, you gave it the kid-gloves treatment, understanding that the brand-new engine needed to be run in and would appreciate a slightly easier start to life. Then, as the novelty wore off and the vehicle began to earn its living, you subconsciously grew a heavier right foot. And it is this that's seen the fuel consumption creep up. Failing that, you might have an on-board computer that has been silently recalibrating itself, perhaps in conjunction with software updates at the dealership which you may, or may not have, been made aware by the dealer. To be perfectly honest, I'd find 6.4-litre per 100km average on a Colorado borderline unbelievable, and the sort of economy only a dedicated fuel-saving driver could even get close to. Ten litres per 100km, meanw

Question 7

My 2012 Holden Colorado is losing engine power over long distances

Accepted Answer

Modern vehicles like the Colorado have lots of sensors to help prevent major engine melt-downs. One of those is the sensor that tells the car the engine oil level is too low for safe operation. If that sensor is sending bad information to the car's computer, the vehicle might be programmed to go into limp-home mode or even shut down altogether to preserve the engine. But the oil problem the car is reporting could also be dangerously low oil pressure or oil that has become too hot. The farther and faster you travel, the hotter the oil becomes (up to a point) and the thinner it becomes, meaning it may not be thick enough to sustain safe oil pressure. This could also be caused by a dud sensor, but it could also be a real situation. And like the low oil level sensor, this can force the engine into shutting itself down as a self-preservation measure.

Question 8

My 2009 Holden Colorado has been going into limp mode

Accepted Answer

It sounds counter-intuitive that an engine would run at all with the crank angle sensor removed. Generally, without this sensor working properly, the fuel-injection system has no idea when to inject the fuel or fire the spark plugs. But sometimes – as in this engine – if the computer can't 'find' a crank angle input, it will take a reference from the camshaft angle sensor and use that to time the injection and ignition. Even so, if the problem persists after two replacement sensors, it's probably fair to say this particular sensor is either not the root of your problem, or that or the engine's wiring is frying the new sensors as fast as you're changing them. Either way, a trip to an auto electrician seems like the next logical step. Chances are a switched on sparkie will have seen this exact problem before and will know how to deal with it or at least take the logical steps to diagnose what's going wrong. Simply continuing to change bits and pieces is often an expensive way to solve a problem like this.

Question 9

How to deactivate hill assist in a 2019 Holden Colorado

Accepted Answer

I'm curious to know what happened when the hill-start assistance kicked in on the flat. Since this system holds the car on a hill so you can move off easily, it should deactivate as soon as you press the throttle to move. Which means, on a flat surface, you shouldn't be able to feel the system at all. Are you sure this is what's happening. Could the problem instead be a brake caliper that is sticking on, or a hand-brake that is dragging? In any case, the hill-start system is controlled by sensors that detect that you're parked on a slope and then apply the brakes to stop you rolling back. If any of these sensors is kaput or not sending the correct signal back to the computer, the set-up won't work properly. Conceivably it could engage on the flat but, again, I don't know how you would know. But the solution is a simple one; take the vehicle to a Holden dealer who will be able to figure out what's wrong and then fix the problem under warranty. Your car is covered by a five-year warranty, so make the most of it. By the way, disconnecting safety gear is not the best way to go as it can (obviously) make the car less inherently safe and, in some, cases even render the vehicle technically unroadworthy.

Question 10

Water leak in my 2009 Holden Colorado

Accepted Answer

Here's a pointed question: Does your vehicle have an aftermarket trailer-brake system fitted? If it does, it's quite likely that the wiring passes through the cabin somewhere near where your leak is located. Unless this access hole is correctly sealed with the proper grommet, there's every chance water is getting in at this point. Other likely suspects for this include roof mounted aerial holes, roof rack attachment points and even worn or damaged window and door rubbers.

Holden Colorado 2012 Problems

Colorado LXR wheel nut update

Holden Colorado: Can driving 4WD on bitumen road cause damage?

Search from Over 8,000 questions Over 8,000 questions answered by CarsGuide

Complete Guide to Holden
Colorado

Holden Colorado 2012 Problems

Colorado LXR wheel nut update

Holden Colorado: Can driving 4WD on bitumen road cause damage?

Search from Over 8,000 questions Over 8,000 questions answered by CarsGuide

Related cars for sale

cars

guide

Complete Guide to HoldenColorado

Complete Guide to Holden
Colorado